
Technically reviewed by Vincent, Founder at HEXVARO
Last reviewed
Quick answer
Quick answer: what to specify
Name the coating standard (ISO 10684 for metric M8–M64, ASTM F2329 for inch), the thread-fit method (nuts tapped oversize after coating to 6AZ or 6AX is the usual one), and the property class. Expect about 50 µm of zinc on the threads. Order bolts and nuts galvanized together from one source, and do not galvanize class 12.9 or ASTM A490 bolts.
| Grade | Hot-dip galvanizing |
|---|---|
| 4.6, 4.8, 5.6, 8.8 | Yes |
| 10.9 | With care |
| 12.9 | No |
| ASTM A490 | No |
Which standard applies
| Standard | Covers | Notes |
|---|---|---|
| ISO 10684 | Metric coarse-thread fasteners M8–M64 | Process, thread fit, coating thickness and assembly strength. Adopted in the Gulf as GSO ISO 10684. |
| ASTM F2329 | Inch bolts, nuts, washers and studs | Zinc thickness by size, adherence and embrittlement controls. Referenced by ASTM F3125 and A563. |
| ISO 1461 | General steel articles | Batch galvanizing of fabricated steel. Fasteners are usually ordered to ISO 10684 instead. |
| ASTM A153 | Iron and steel hardware | Older general hardware standard still seen on drawings. |
Coating thickness
Spun hot-dip galvanizing on threaded fasteners larger than 6 mm gives a mean coating of at least 50 µm, with no single reading below 40 µm. Electroplated zinc is usually 5 to 12 µm, so the galvanized coating lasts many times longer in outdoor and coastal service.
ASTM F2329 sets a similar level for inch fasteners: about 0.002 in (50 µm) on bolts and nuts over 3/8 in diameter, and slightly less on smaller sizes.
Why galvanized nuts are tapped oversize
The zinc layer adds thickness to the bolt thread, so a normal nut will not run on. ISO 10684 allows two methods. The common one is to tap nuts oversize after galvanizing, to tolerance class 6AZ or 6AX, and mate them with normal-thread bolts. The other is to cut the bolt thread undersize before galvanizing (6az) and use normal nuts. Never mix the two methods, because an oversize nut on an undersize bolt loses strength.
- Oversize nuts are marked Z or X; undersize bolts are marked U.
- Buy bolts and nuts from the same galvanized lot so the fit is controlled.
- Plain nuts will not fit galvanized bolts, and galvanized nuts are loose on plain bolts.
Grades that can and cannot be galvanized
| Grade | Hot-dip galvanizing | Comment |
|---|---|---|
| 4.6, 4.8, 5.6, 8.8 | Yes | The usual galvanized range for structures and supports |
| 10.9 | With care | Permitted under ISO 10684; agree process controls with the supplier |
| 12.9 | No | Hydrogen embrittlement risk; use zinc flake instead |
| ASTM A325 / A563 DH / F436 | Yes | Supplied as galvanized sets; nuts overtapped and lubricated |
| ASTM A490 | No | ASTM F3125 does not allow hot-dip galvanizing of A490 |
| ASTM F1554 anchor bolts | Yes | Common for column bases; often galvanized on the threaded end only |
Hot-dip galvanized vs other coatings
- Zinc plating: thin and bright, low cost, for indoor or painted assemblies.
- Zinc flake: thin, no hydrogen from processing, suits 10.9 and 12.9 and tight thread fits.
- Hot-dip galvanizing: thick and durable outdoors, but needs the matched thread fit above.
- PTFE (fluoropolymer): low friction for flange studs, often applied over a zinc or phosphate base.
What to put in a galvanized-fastener RFQ
- Standard, size, length and property class or ASTM grade for each line.
- Coating standard: ISO 10684 or ASTM F2329, and any higher thickness requirement.
- Thread-fit method, and whether nuts and washers are supplied galvanized in the same order.
- Quantity per size, packing (sets or bulk) and the inspection report you need, such as coating thickness readings.
Frequently asked questions
How thick is hot-dip galvanizing on bolts?
For metric fasteners above 6 mm, ISO 10684 calls for a mean of at least 50 µm and a local minimum of 40 µm. Inch fasteners over 3/8 in to ASTM F2329 are coated to a similar level.
Why won't a normal nut fit a galvanized bolt?
The zinc coating makes the bolt thread larger. Galvanized nuts are tapped oversize after coating (6AZ or 6AX) to fit, so bolts and nuts must be ordered as a galvanized set.
Can 10.9 bolts be hot-dip galvanized?
ISO 10684 covers property classes up to 10.9, but the process needs extra control. Class 12.9 bolts and ASTM A490 bolts should not be hot-dip galvanized.
Is hot-dip galvanized better than zinc plated?
For outdoor and coastal use, yes: the coating is several times thicker and lasts much longer. Zinc plating is cheaper and suits indoor or painted assemblies.
What is the MOQ for galvanized fasteners from HEXVARO?
The reference MOQ is 500 pcs per size, with mixed sizes welcome on one order. Bolts, nuts and washers are galvanized and supplied together as matched sets.
Products to this standard